Jump to content
tim3lord

apds-9960 Gesture Sensor Working on TM4C1294XL

Recommended Posts

Hello, I am trying to port Sparkfun's library to get the apds-9960 Gesture Sensor working on my Tiva C 1294 board.  I set up the library like you normally would with ardunio while changing the interrupt pin and uploaded the code to my board with no issues.  The only problem is when I go to serial monitor I get nothing printed to screen.  Are there any other steps I need to take in order to convert this code to work on my Tiva board?  I also tried moving to code composer studio but I cant find many clean tutorials on how to use it.  I also have a MSP432 that I might try to get his working on if its supported better. 

Thanks!

 

/****************************************************************
GestureTest.ino
APDS-9960 RGB and Gesture Sensor
Shawn Hymel @ SparkFun Electronics
May 30, 2014
https://github.com/sparkfun/APDS-9960_RGB_and_Gesture_Sensor

Tests the gesture sensing abilities of the APDS-9960. Configures
APDS-9960 over I2C and waits for gesture events. Calculates the
direction of the swipe (up, down, left, right) and displays it
on a serial console. 

To perform a NEAR gesture, hold your hand
far above the sensor and move it close to the sensor (within 2
inches). Hold your hand there for at least 1 second and move it
away.

To perform a FAR gesture, hold your hand within 2 inches of the
sensor for at least 1 second and then move it above (out of
range) of the sensor.

Hardware Connections:

IMPORTANT: The APDS-9960 can only accept 3.3V!
 
 Arduino Pin  APDS-9960 Board  Function
 
 3.3V         VCC              Power
 GND          GND              Ground
 A4           SDA              I2C Data
 A5           SCL              I2C Clock
 2            INT              Interrupt

Resources:
Include Wire.h and SparkFun_APDS-9960.h

Development environment specifics:
Written in Arduino 1.0.5
Tested with SparkFun Arduino Pro Mini 3.3V

This code is beerware; if you see me (or any other SparkFun 
employee) at the local, and you've found our code helpful, please
buy us a round!

Distributed as-is; no warranty is given.
****************************************************************/

#include <Wire.h>
#include <SparkFun_APDS9960.h>

// Pins
#define APDS9960_INT    PE_4 // Needs to be an interrupt pin

// LED
#define LED PN_0

// Constants

// Global Variables
SparkFun_APDS9960 apds = SparkFun_APDS9960();
int isr_flag = 0;

void setup() {

  pinMode(LED, OUTPUT);  

  // Set interrupt pin as input
  pinMode(APDS9960_INT, INPUT);
  Wire.setModule(0);
  Wire.begin();
  

  // Initialize Serial port
  Serial.begin(9600);
  Serial.println();
  Serial.println(F("--------------------------------"));
  Serial.println(F("SparkFun APDS-9960 - GestureTest"));
  Serial.println(F("--------------------------------"));
  
  // Initialize interrupt service routine
  attachInterrupt(0, interruptRoutine, FALLING);

  // Initialize APDS-9960 (configure I2C and initial values)
  if ( apds.init() ) {
    Serial.println(F("APDS-9960 initialization complete"));
  } else {
    Serial.println(F("Something went wrong during APDS-9960 init!"));
  }
  
  // Start running the APDS-9960 gesture sensor engine
  if ( apds.enableGestureSensor(true) ) {
    Serial.println(F("Gesture sensor is now running"));
  } else {
    Serial.println(F("Something went wrong during gesture sensor init!"));
  }
}

void loop() {
  if( isr_flag == 1 ) {
    detachInterrupt(0);
    handleGesture();
    isr_flag = 0;
    attachInterrupt(0, interruptRoutine, FALLING);
  }
}

void interruptRoutine() {
  isr_flag = 1;
}

void handleGesture() {
    if ( apds.isGestureAvailable() ) {
    switch ( apds.readGesture() ) {
      case DIR_UP:
        Serial.println("UP");
        digitalWrite(LED, HIGH);   // turn the LED on (HIGH is the voltage level)
        delay(1000);               // wait for a second
        digitalWrite(LED, LOW);    // turn the LED off by making the voltage LOW
        delay(1000);               // wait for a second
        break;
      case DIR_DOWN:
        Serial.println("DOWN");
        digitalWrite(LED, HIGH);   // turn the LED on (HIGH is the voltage level)
        delay(1000);               // wait for a second
        digitalWrite(LED, LOW);    // turn the LED off by making the voltage LOW
        delay(1000);               // wait for a second
        break;
      case DIR_LEFT:
        Serial.println("LEFT");
        digitalWrite(LED, HIGH);   // turn the LED on (HIGH is the voltage level)
        delay(1000);               // wait for a second
        digitalWrite(LED, LOW);    // turn the LED off by making the voltage LOW
        delay(1000);               // wait for a second
        break;
      case DIR_RIGHT:
        Serial.println("RIGHT");
        digitalWrite(LED, HIGH);   // turn the LED on (HIGH is the voltage level)
        delay(1000);               // wait for a second
        digitalWrite(LED, LOW);    // turn the LED off by making the voltage LOW
        delay(1000);               // wait for a second
        break;
      case DIR_NEAR:
        Serial.println("NEAR");
        digitalWrite(LED, HIGH);   // turn the LED on (HIGH is the voltage level)
        delay(1000);               // wait for a second
        digitalWrite(LED, LOW);    // turn the LED off by making the voltage LOW
        delay(1000);               // wait for a second
        break;
      case DIR_FAR:
        Serial.println("FAR");
        digitalWrite(LED, HIGH);   // turn the LED on (HIGH is the voltage level)
        delay(1000);               // wait for a second
        digitalWrite(LED, LOW);    // turn the LED off by making the voltage LOW
        delay(1000);               // wait for a second
        break;
      default:
        Serial.println("NONE");
    }
  }
}

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...