Jump to content
Sign in to follow this  
mediguejc

MSP430FR5994 Launchpad and I2C Module 2

Recommended Posts

Hello for information.

I work in this moment for data logger. I need 2 SPI port (LCD and SD) and 1 I2C port (sensors). I Use TI MSP430FR5994 Launchpad.

With Energia E18, impossible to use SCL (2), SDA (2), pin 9 and 10. (I need Pin 14,15 for I2C/SPI LCD, and I need Pin 48, 50 already connected on SD connector in launchpad), 

 

1) don't forget to setup I2C module number:       Wire.setModule(2);          

 

2) modify Pins_Energia.h as describe bellow   in  \Local\Energia15\packages\energia\hardware\msp430\1.0.3\variants\MSP-EXP430FR5994LP

 (see link in Energia Preference menu).    Select ' PORT_SELECTION0'

________________________________________________________________________________________________________________________________

#ifndef Pins_Energia_h
#define Pins_Energia_h
#ifndef BV
#define BV(x) (1 << (x))
#endif

// Attribute for placing R/W variables in FRAM
// Example
//      uint8_t DisplayBuffer[LCD_MAXIMUM_Y][LCD_MAXIMUM_X] PLACE_IN_FRAM;
#define PLACE_IN_FRAM __attribute__((section(".text")))

#if defined(__MSP430_HAS_EUSCI_B0__)
static const uint8_t SS0     = 47;  /* P4.0 */
static const uint8_t SCK0    = 49;  /* P2.2 */
static const uint8_t MOSI0   = 48;  /* P1.6 aka SIMO */
static const uint8_t MISO0   = 50;  /* P1.7 aka SOMI */
static const uint8_t SS1     = 8;   /* P6.3 */
static const uint8_t SCK1    = 7;   /* P5.2 */
static const uint8_t MOSI1   = 15;  /* P5.0 aka SIMO */
static const uint8_t MISO1   = 14;  /* P5.1 aka SOMI */
static const uint8_t TWISDA0 = 48;  /* P1.6 UCB0 */
static const uint8_t TWISCL0 = 50;  /* P1.7 UCB0 */
static const uint8_t TWISDA1 = 15;  /* P5.0 UCB1 */
static const uint8_t TWISCL1 = 14;  /* P5.1 UCB1 */
static const uint8_t TWISDA2 = 10;  /* P7.0 UCB2 */
static const uint8_t TWISCL2 = 9;   /* P7.1 UCB2 */
#define TWISDA0_SET_MODE (PORT_SELECTION1 | INPUT_PULLUP)
#define TWISCL0_SET_MODE (PORT_SELECTION1 | INPUT_PULLUP)
#define TWISDA1_SET_MODE (PORT_SELECTION0 | INPUT_PULLUP)
#define TWISCL1_SET_MODE (PORT_SELECTION0 | INPUT_PULLUP)
#define TWISDA2_SET_MODE (PORT_SELECTION1 | INPUT_PULLUP)       #define TWISDA2_SET_MODE (PORT_SELECTION0 | INPUT_PULLUP)
#define TWISCL2_SET_MODE (PORT_SELECTION1 | INPUT_PULLUP)        #define TWISCL2_SET_MODE (PORT_SELECTION0 | INPUT_PULLUP)
#define SPISCK0_SET_MODE  (PORT_SELECTION1)
#define SPIMOSI0_SET_MODE (PORT_SELECTION1)
#define SPIMISO0_SET_MODE (PORT_SELECTION1)
#define SPISCK1_SET_MODE  (PORT_SELECTION0)
#define SPIMOSI1_SET_MODE (PORT_SELECTION0)
#define SPIMISO1_SET_MODE (PORT_SELECTION0)

.............................................................................................................

__________________________________________________________________________________________________________________________________________________

 

Best regards.  MJC.

 

 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×