Jump to content
43oh

Recommended Posts

I have the chip number MSP430FR6989 and I want to use it to read 10 analog DC signals then do some processing (multiply them by certain factors) after that I want to convert them back to analog using PWM and RC filter, my issue is in the second part , how to use timers( set period , duty cycles) of the MSP430 to produce PWMs from the analog inputs.  
This is the code:

#include <msp430.h>
#define ACLK 0x0100 // Timer ACLK source
#define UP 0x0010 // Timer UP mode
#define ENABLE_PINS 0xFFFE // Required to use inputs and outputs
#define ENABLE_PINS   0xFFFE // Enables inputs and outputs
void ADC_SETUP(void); // Used to setup ADC12 peripheral
const int x1=1;
const int x2=1;
volatile int multiplied_value,duty;

main()
{
  PM5CTL0 = ENABLE_PINS; // Enable inputs and outputs
P1DIR =BIT0; // Set RED LED to output


ADC_SETUP(); // Sets up ADC peripheral
while(1)
{
ADC12CTL0 = ADC12CTL0 | ADC12ENC; // Enable conversion
ADC12CTL0 = ADC12CTL0 | ADC12SC; // Start conversion
while  ( ADC12BUSY == 1){
multiplied_value = (ADC12MEM0);
if (multiplied_value > 0x800) // If input > 1.65V
{
P1OUT = BIT0; // Turn on red LED
}
else // Else input <= 1.65V
{
P1OUT = 0x00; // Turn off red LED
}


P1DIR |= BIT5;             // P1.5 to output
P1SEL1 |= BIT5;             // P1.5 to TA0.1


 TA0CCTL1 = OUTMOD_7;          // CCR1 reset/set
 TA0CCR1 = multiplied_value*65536/3.3 ;
 duty=TA0CCR1;// CCR1 PWM duty cycle
 TA0CCR0 =1000;             // PWM Period
 TA0CTL = TASSEL_2 + MC_1;   // SMCLK, up mode

 _BIS_SR(LPM0_bits);        // Enter LPM0
}
}
}
void ADC_SETUP(void)
{
#define ADC12_SHT_16 0x0200 // 16 clock cycles for sample and hold
#define ADC12_ON 0x0010 // Used to turn ADC12 peripheral on
#define ADC12_SHT_SRC_SEL 0x0200 // Selects source for sample & hold
#define ADC12_12BIT 0x0020 // Selects 12-bits of resolution
#define ADC12_P92 0x000A // Use input P9.2 for analog input
//#define ADC12_P43 0x000A
//#define ADC12_P32 0x000A
//#define ADC12_P93 0x000A
//#define ADC12_P14 0x000A
//#define ADC12_P20 0x000A
//#define ADC12_P41 0x000A
ADC12CTL0 = ADC12_SHT_16 | ADC12_ON ; // Turn on, set sample & hold time
ADC12CTL1 = ADC12_SHT_SRC_SEL; // Specify sample & hold clock source
ADC12CTL2 = ADC12_12BIT; // 12-bit conversion results
ADC12MCTL0 = ADC12_P92; // P9.2 is analog input
//ADC12MCTL1 = ADC12_P43;
}

 

 

I have the voltmeter, when I measure the frquency at the pin1.5 it gives me a number reanges between 14kHz to 0.11..   

I'm not sure if I used PWM correctly?

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...