Jump to content
43oh

Search the Community

Showing results for tags 'tx'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • News
    • Announcements
    • Suggestions
    • New users say Hi!
  • Spotlight!
    • Sponsor Spotlight
    • Sponsor Giveaways
  • Energia
    • Energia - MSP
    • Energia - TivaC/CC3XXX
    • Energia - C2000
    • Energia Libraries
  • MSP Technical Forums
    • General
    • Compilers and IDEs
    • Development Kits
    • Programmers and Debuggers
    • Code vault
    • Projects
    • Booster Packs
    • Energia
  • Tiva-C, Hercules, CCXXXX ARM Technical Forums
    • General
    • SensorTag
    • Tiva-C, Hercules, CC3XXX Launchpad Booster Packs
    • Code Vault
    • Projects
    • Compilers and IDEs
    • Development Kits and Custom Boards
  • Beagle ARM Cortex A8 Technical Forums
    • General
    • Code Snippets and Scripts
    • Cases, Capes and Plugin Boards
    • Projects
  • General Electronics Forum
    • General Electronics
    • Other Microcontrollers
  • Connect
    • Embedded Systems/Test Equipment Deals
    • Buy, Trade and Sell
    • The 43oh Store
    • Community Projects
    • Fireside Chat
  • C2000 Technical Forums
    • General
    • Development Kits
    • Code Vault
    • Projects
    • BoosterPacks

Calendars

There are no results to display.


Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


Website URL


Location


Interests


Sparkfun


Github

Found 4 results

  1. Hi. I seem to get the following error whenever I try using "GPIOPinConfigure()" as shown below: However I do NOT get the error whenever the function "GPIOPinConfigure()" is NOT used: In essence, I want to be able to make a SSI connection with two TM4C123GH6PM launchpads in order to send temperature information (from one end) and print it onto a Kentec LCD screen (at the other end). The complete code of the sender is posted in the following: #include <LiquidCrystal.h> #include <DHT.h> #include <st
  2. Hello, I want to make a wireless thermometer using two microcontrollers. How do I write the code in Energia to transmit and receive a variable using a 433 Mhz RF module? Transmitter Setup: I have a TM4C123G connected to a RF transmitter using TX(3) pin 34 on the MCU. The TM4C123G is also connected to a LM34DZ Temp sensor. I need help to modify this working code to send the temperature variable using tx(3) pin 34 /*TM4C123G*/ //initializes/defines the output pin of the LM34 temperature sensor int outputpin= A11; // (pin # 2), use A11 analog input //---------------
  3. Is there a way to use the SoftwareSerial library on the Stellaris Launchpad TM4C123GXL board? I am trying to connect a Sparkfun serial enabled LCD screen to the board but the SoftwareSerial library is only compatible with 20, 16, and 8 MHz processors, and the TM4C123GXL is an 80 MHz chip. How can I use this LCD screen with the Stellaris Launchpad over a UART connection? Do I need to use SoftwareSerial or can I do without it? I am programming in Energia 0101E0017 on Windows 7 64 bit. Any help is greatly appreciated, thanks!
  4. Hi I'm new with energia and I'm trying to use the Hardware serial communication with a Lauchpad Rev. 1.4 so I connect the RX end TX jumpers in cross but it doesn't work...Can anyone help me? this is the simple code I use: void setup() { Serial.begin(9600); } void loop() { Serial.println("Hello !!!"); delay(500); } I try to use also the software serial communication for but it doesn't work
×
×
  • Create New...