Jump to content

Search the Community

Showing results for tags 'salvage'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • News
    • Announcements
    • Suggestions
    • New users say Hi!
  • Spotlight!
    • Sponsor Spotlight
    • Sponsor Giveaways
  • Energia
    • Energia - MSP
    • Energia - TivaC/CC3XXX
    • Energia - C2000
    • Energia Libraries
  • MSP Technical Forums
    • General
    • Compilers and IDEs
    • Development Kits
    • Programmers and Debuggers
    • Code vault
    • Projects
    • Booster Packs
    • Energia
  • Tiva-C, Hercules, CCXXXX ARM Technical Forums
    • General
    • SensorTag
    • Tiva-C, Hercules, CC3XXX Launchpad Booster Packs
    • Code Vault
    • Projects
    • Compilers and IDEs
    • Development Kits and Custom Boards
  • Beagle ARM Cortex A8 Technical Forums
    • General
    • Code Snippets and Scripts
    • Cases, Capes and Plugin Boards
    • Projects
  • General Electronics Forum
    • General Electronics
    • Other Microcontrollers
  • Connect
    • Embedded Systems/Test Equipment Deals
    • Buy, Trade and Sell
    • The 43oh Store
    • Community Projects
    • Fireside Chat
  • C2000 Technical Forums
    • General
    • Development Kits
    • Code Vault
    • Projects
    • BoosterPacks

Calendars

There are no results to display.


Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


Website URL


Location


Interests


Sparkfun


Github

Found 1 result

  1. Since my only 5529LP was confirmed no longer functioning properly and the likely cause is the USB hub module, there have been some thoughts going through my mind to salvage the core 5529 device on the LP for some good use. And this weekend I have decided to give it a try. As the USB host part is confirmed not functioning, the first step is to verify the F5529 is still good. The easiest way is to try program it and check if it can run new program. With a good F5529 LP (the new replacement board ordered after the old one retired), I removed all the jumpers between the ez-FET and the target device, and then wired the GND, 5V, 3V3, RXD, TXD, SBW RST, and SBW TST from the good ez-FET to the 5529 side of the old LP. This will also power up the old board from the new one as the USB host on the old board is dead and no longer powering it. Soon after an example Energia sketch of SerialCallResponseASCII is uploaded through the new, good board, the good news is displayed on the Serial console confirming the 5529 device is still working flawlessly. At this point, I came into realization that this board can no longer be a handy development board as it once was but only good for deployment, possibly permanently, to some project because I have to rely on that good LP every time for programming. But wait, I recall recently from the forum there are some posts mentioning Forth interpreter for MSP430, one of which by monsonite with comprehensive information on various Forth offerings. However, a common requirement for Forth is serial communication for the console that my old LP is no longer capable to provide with a dead USB hub. Even though I don't have serial to usb converter to bypass the on-board hub for direct serial connection, I remember there is an old Arduino Pro Mini laying around without much used. Combining these two, I could probably build a utility development board that provide ad hoc programming capability (in Forth) on the 5529LP provide the console access required by Forth on the 5529LP via the Arduino Pro Mini (forward the serial communication from the Arduino UART to the 5529LP TX/RX) power the 5529LP via the 5V and 3V3 pin from the Arduino Pro Mini All in all, the goal is to take the Arduino Pro Mini as the controller or programmer of the 5529LP that is programmed to run Forth only. I picked the Mecrisp as it provided out of the box support for the 5529LP and pre-compiled hex file. So the build begin by first flashing the Forth hex file to the 5529LP. Again it required a good 5529LP and I used the latest MSPFlasher for the job. The following is the command line (for Windows). MSP430Flasher.exe -w "forth-mecrisp-5529.hex" -v -g -z [VCC] For a more decent looking of this utility development board, the Pro Mini is mounted to a medium sized breadboard on one end, and with four metal pins (pulled from left over connectors), the 5529LP is somehow "mounted" to the other end. This is enough for some structural support for the 5529LP Now for the Arduino side. Since there is only one set of UART on the Pro Mini, the program on it make use of the SoftSerial library that will emulate another serial port by two digital pins to relay the serial messages from the real UART to the 5529LP. Finally the moment of truth, the serial console to the Arduino is opened for a test. Apart from the line feed being weird, the expression run (1 2 + .<cr>) is successful, so is the programming of the blinky program Moving forward, the Arduino can be programmed in such a way that not only merely relaying serial message, but parse special commands to initiate specific Forth programming to the 5529LP (the Forth programs themselves stored as program in the Arduino). Hopefully this will make the whole package more versatile and practical.
×