Jump to content

Search the Community

Showing results for tags 'RedBearLab'.

More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • News
    • Announcements
    • Suggestions
    • New users say Hi!
  • Spotlight!
    • Sponsor Spotlight
    • Sponsor Giveaways
  • Energia
    • Energia - MSP
    • Energia - TivaC/CC3XXX
    • Energia - C2000
    • Energia Libraries
  • MSP Technical Forums
    • General
    • Compilers and IDEs
    • Development Kits
    • Programmers and Debuggers
    • Code vault
    • Projects
    • Booster Packs
    • Energia
  • Tiva-C, Hercules, CCXXXX ARM Technical Forums
    • General
    • SensorTag
    • Tiva-C, Hercules, CC3XXX Launchpad Booster Packs
    • Code Vault
    • Projects
    • Compilers and IDEs
    • Development Kits and Custom Boards
  • Beagle ARM Cortex A8 Technical Forums
    • General
    • Code Snippets and Scripts
    • Cases, Capes and Plugin Boards
    • Projects
  • General Electronics Forum
    • General Electronics
    • Other Microcontrollers
  • Connect
    • Embedded Systems/Test Equipment Deals
    • Buy, Trade and Sell
    • The 43oh Store
    • Community Projects
    • Fireside Chat
  • C2000 Technical Forums
    • General
    • Development Kits
    • Code Vault
    • Projects
    • BoosterPacks


There are no results to display.

Found 3 results

  1. Hi All, This is my first post on the forum so apologize of any mistakes. So, yesterday I bought Redbearlab CC3200 Wifi Mini from Amazon. The out-of-box test successfully executed with the LED toggling on/off based on the button pressed on 192.168.11. But when I tried to upload the program using Energia, it was failed. Here is the message from Energia which I copy and paste it directly. Ubable to find RedBearLabs board: 1 Using HID to reset for RedBearLab board Opening \\.\COM40 Triggering bootloader.... Getting storage list Bootloader Version: 4 Silicon version ES1.32 or higher Bootloader version is 2, 1, 4, 0 It's a CC3200 device: PG1.33 or higher Switch UART pinmux to APPS Switch to NWP bootloader complete Load common boot command for PG1.33 or higher Bootloader version is 2, 0, 4, 0 BlockSize is 4096, number of blocks is 16 erasing 13 blocks starting from 0 I am using Eenergia-0101E0017. I have followed the "getting startup guide" from Energia, pay attention closely to the driver and check the COM port (mine is COM40), also have updated MK20 firmware. But still, those error occured. And this wasn't the end of story.... After that, I put my laptop to sleep, went to office, turned on my laptop, and I used the same USB port to charge my android phone. 8 hours later, I put my laptop back to sleep, went to home and then I turned back on my laptop.This time, I tried again to upload my Wifi Mini using Energia, and boom, Done flashing successfully. So until now, if I have a problem "failed to upload" using Energia, I repeat those steps: 1. make my laptop sleep. 2. wake up my laptop, connect android phone to the USB port. 3. make my laptop sleep again. 4. disconnect my android phone from USB port. 5. wake up my laptop. 6. connect wifi mini to USB port, open Energia and start flashing. Done. So, anyone have the explanation about this? Thank you.
  2. i tried without luck all the WS2812 / WS2811 related libraries shown at http://energia.nu/reference/libraries/ they all seem to address different mcu types (?) like https://github.com/ILAMtitan/WS2811Driver complains: 0: fatal error: msp430.h: No such file or directory #include <msp430.h> ^ compilation terminated. and the adafruit neopixel lib for arduino: simple.cpp:5:23: fatal error: avr/power.h: No such file or directory #include <avr/power.h> ^ compilation terminated. actually i need to address only one single WS2812 led. could please point me to the right lib/solution if it already exists ? thanks a lot
  3. hello, i'm new here and confused where i should place my redbearlab CC3200 wifi mini topics ? my first question would be if there is any WS2812 (neopixel) support for the wifi mini ? thanks