Jump to content
43oh

stanley

Members
  • Content Count

    5
  • Joined

  • Last visited

Reputation Activity

  1. Like
    stanley got a reaction from gssmahadevan in [Energia Library] Nordic nRF24L01+ library   
    Before I forget, I quickly documented the entire process on my blog http://arduino-for-beginners.blogspot.com/2013/11/stellaris-launchpad-with-nrf24l01.html
  2. Like
    stanley got a reaction from Automate in [Energia Library] Enrf24 nRF24L01+ Library   
    Wrote a blog on the process of getting nRF24L01 working with Stellaris Launchpad and Arduino UNO running on RF24 library...
     
    They are only a few combinations to try if they are not working :-
     
    Air rate / speed :- 250Kbps, 1Mbps or 2Mbps
    Channels : both sides MUST matched the same channel
    txaddress matches rxaddress ( or vice versa )
    CRC : Either OFF or 8bit or 16bit ( Mirf & enrf24 uses 8bit CRC, RF24 uses 16bit CRC or manually set it )
     
     
    http://arduino-for-beginners.blogspot.com/2013/11/stellaris-launchpad-with-nrf24l01.html
  3. Like
    stanley got a reaction from bluehash in [Energia Library] Nordic nRF24L01+ library   
    Before I forget, I quickly documented the entire process on my blog http://arduino-for-beginners.blogspot.com/2013/11/stellaris-launchpad-with-nrf24l01.html
  4. Like
    stanley got a reaction from Automate in [Energia Library] Nordic nRF24L01+ library   
    Dear Spirilis,
     
    Thanks for the quick replies...
    After a few tweaks, I manage to get the StellarPad working with my Arduino UNO !!!
     
    Thank you :-)
     
     
     
    Here are the setting to get it working with Arduino RF24 libraries :-
     
    // This address must matched any of the receiving address/pipes on the UNO
    const uint8_t txaddr[] = { 0xDE, 0xDE, 0xDE, 0xDE, 0xE3 };   // Match UNO bitrate to 1Mbps   radio.begin(1000000);  // Defaults 1Mbps    // Channel number must match   radio.setChannel(88);   // The CRC was set to 16bit, so set to 16 bit, 1st number turn on/off CRC, 2nd number turn on/off 8 or 16bit   radio.setCRC(1,1);     Here are my Serial Monitor on the UNO side :-   Got payload: ON len:2  Got payload: OFF len:3  Got payload: ON len:2  Got payload: OFF len:3  Got payload: ON len:2      Anyone else that needed help to get the enrf24 libs working with Uno/attiny/Raspberry Pi can contact me or post here...      Stanley
  5. Like
    stanley got a reaction from spirilis in [Energia Library] Nordic nRF24L01+ library   
    Before I forget, I quickly documented the entire process on my blog http://arduino-for-beginners.blogspot.com/2013/11/stellaris-launchpad-with-nrf24l01.html
  6. Like
    stanley got a reaction from spirilis in [Energia Library] Nordic nRF24L01+ library   
    Dear Spirilis,
     
    Thanks for the quick replies...
    After a few tweaks, I manage to get the StellarPad working with my Arduino UNO !!!
     
    Thank you :-)
     
     
     
    Here are the setting to get it working with Arduino RF24 libraries :-
     
    // This address must matched any of the receiving address/pipes on the UNO
    const uint8_t txaddr[] = { 0xDE, 0xDE, 0xDE, 0xDE, 0xE3 };   // Match UNO bitrate to 1Mbps   radio.begin(1000000);  // Defaults 1Mbps    // Channel number must match   radio.setChannel(88);   // The CRC was set to 16bit, so set to 16 bit, 1st number turn on/off CRC, 2nd number turn on/off 8 or 16bit   radio.setCRC(1,1);     Here are my Serial Monitor on the UNO side :-   Got payload: ON len:2  Got payload: OFF len:3  Got payload: ON len:2  Got payload: OFF len:3  Got payload: ON len:2      Anyone else that needed help to get the enrf24 libs working with Uno/attiny/Raspberry Pi can contact me or post here...      Stanley
×
×
  • Create New...