Jump to content

  • Log In with Google      Sign In   
  • Create Account

Photo

Freescale Cortex-M0+, Arduino compatible(?) board.


  • Please log in to reply
5 replies to this topic

#1 abecedarian

abecedarian

    Level 4

  • Members
  • 861 posts
  • LocationDundrinkingin Anlimentonic Encastle


Posted 31 October 2012 - 04:07 AM

I know it was posted over on stellarisit.com
http://forum.stellar...t-board-for-13/

But just in case-

"The FRDM-KL25Z is a Development Tool for Kinetis KL25 Series, This Kinetis KL2 MCU family is pin, software and tool compatible with all other Kinetis L families and adds a full-speed USB 2.0 On-The-Go controller with an integrated low-voltage regulator. The Kinetis KL2 MCU family is also compatible with the Kinetis K20 (ARM® Cortex™-M4) family, providing a migration path to higher performance and feature integration.
Devices start from 32 KB of flash in a small-footprint 5 x 5 mm 32 QFN package extending up to 256 KB in a 121 MBGA package. Each combines ultra-low-power performance with a rich suite of analog, communication, timing and control peripherals."

See "Register to qualify for a free board" from the page http://www.futureele...,Nea:True,N:750.
Otherwise, $12.95: http://www.futureele...ONDUCTOR9023990

From the User Manual:
"5.8 Arduino Compatibility
The I/O headers on the FRDM-KL25Z are arranged to allow compatibility with peripheral boards (known as shields) that connect to Arduino™ and Arduino-compatible microcontroller boards. The outer rows of pins (the even numbered pins) on the headers share the same mechanical spacing and placement as the I/O headers on the Arduino Revision 3 (R3) standard."

  • bluehash and yyrkoon like this
Over here, doing "over here" things.

#2 GeekDoc

GeekDoc

    Level 4

  • Administrators
  • 1,393 posts
  • LocationO'Fallon, Illinois (St. Louis Metro area)
  • Sparkfun Wishlist


Posted 31 October 2012 - 12:34 PM

"...The outer rows of pins (the even numbered pins) on the headers share the same mechanical spacing and placement as the I/O headers on the Arduino Revision 3 (R3) standard."


Great... they're perpetuating the spacing mistake that became a standard. :problem:
Public Service Announcement: I am a microcontroller / electronics noob! I should usually be quietly ignored or patiently instructed.
http://blog.DocsTech.net

#3 pine

pine

    Level 2

  • Members
  • 334 posts

Posted 26 January 2013 - 04:55 PM

There is an interesting firmware from CoreBASIC that runs on this board..

 

http://soldercore.co...-freedom-board/



#4 tingo

tingo

    Level 1

  • Members
  • 111 posts
  • LocationOslo, Norway

Posted 27 January 2013 - 06:35 PM

Yes, CoreBASIC on the Freedom board looked interesting.


Torfinn

#5 jpnorair

jpnorair

    Level 3

  • Members
  • 617 posts
  • LocationSan Francisco


Posted 09 February 2013 - 08:05 AM

I'm not crazy about the Kinetis line.  I think the CM0, CM3, and CM4 parts from STMicro are overall the best.


jpnorair: GitHub | Wikipedia | Wiki | Blog | Haytag

#6 yyrkoon

yyrkoon

    Level 3

  • Members
  • 476 posts
  • LocationArizona

Posted 09 February 2013 - 12:08 PM

That reminds me of the old TI LM3S6965 eval kit that cost $75 USD. Minus the OLED and ethernet.


I'm an eye-for-an-eye, tooth-for-a-tooth kind of guy.  -  So you support a system that would leave everyone blind and toothless. -  Not everyone. Just the bad guys.

Youtube channel  Blog





0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users