Search the Community

Showing results for tags 'pin_energia'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • News
    • Announcements
    • Suggestions
    • New users say Hi!
  • Spotlight!
    • Sponsor Spotlight
    • Sponsor Giveaways
  • Energia
    • Energia - MSP
    • Energia - TivaC/CC3XXX
    • Energia - C2000
    • Energia Libraries
  • MSP Technical Forums
    • General
    • Compilers and IDEs
    • Development Kits
    • Programmers and Debuggers
    • Code vault
    • Projects
    • Booster Packs
    • Energia
  • Tiva-C, Hercules, CCXXXX ARM Technical Forums
    • General
    • SensorTag
    • Tiva-C, Hercules, CC3XXX Launchpad Booster Packs
    • Code Vault
    • Projects
    • Compilers and IDEs
    • Development Kits and Custom Boards
  • Beagle ARM Cortex A8 Technical Forums
    • General
    • Code Snippets and Scripts
    • Cases, Capes and Plugin Boards
    • Projects
  • General Electronics Forum
    • General Electronics
    • Other Microcontrollers
  • Connect
    • Embedded Systems/Test Equipment Deals
    • Buy, Trade and Sell
    • The 43oh Store
    • Community Projects
    • Fireside Chat
  • C2000 Technical Forums
    • General
    • Development Kits
    • Code Vault
    • Projects
    • BoosterPacks

Calendars

There are no results to display.


Found 1 result

  1. Hello, everyone! Don't know if @Rei Vilo or @energia would like to make a suggestion, but I hope so! I'm working on a project using the CC3200Mod. The PCB should be ready later this week and I'd like to give the designer a basic firmware file to test it. This was no problem on the launchpad, but after we went over the schematic, we found that the pin layout is very different between the CC3200 and the CC3200Mod. Working with launchpads doesn't make a difference, but the PCB doesn't have those ports available, everything is connected to the pin on the chip. Will I be better off by modifying my pin_energia.h file to represent the CC32000MOD's layout or should I map the individual GPIOs in my sketch? Current pin_energia.h (matches CC32000 pin out): const uint16_t digital_pin_to_pin_num[] = { NOT_A_PIN, /* dummy */ NOT_A_PIN, /* 1 - 3.3V */ PIN_58, /* 2 - GPIO_03 */ PIN_04, /* 3 - GPIO_13 */ PIN_03, /* 4 - GPIO_12 */ PIN_61, /* 5 - GPIO_06 */ PIN_59, /* 6 - GPIO_04 */ PIN_05, /* 7 - GPIO_14 */ PIN_62, /* 8 - GPIO_07 */ PIN_01, /* 9 - GPIO_10 */ PIN_02, /* 10 - GPIO_11 */ PIN_15, /* 11 - GPIO_22 */ PIN_55, /* 12 - GPIO_01 */ PIN_21, /* 13 - GPIO_25 */ PIN_06, /* 14 - GPIO_15 */ PIN_07, /* 15 - GPIO_16 */ NOT_A_PIN, /* 16 - RESET */ PIN_45, /* 17 - GPIO_31 */ PIN_08, /* 18 - GPIO_17 */ PIN_18, /* 19 - GPIO_28 */ NOT_A_PIN, /* 20 - GND */ NOT_A_PIN, /* 21 - 5V */ NOT_A_PIN, /* 22 - GND */ PIN_57, /* 23 - GPIO_02 */ PIN_60, /* 24 - GPIO_05 */ PIN_58, /* 25 - GPIO_03 */ PIN_59, /* 26 - GPIO_04 */ PIN_63, /* 27 - GPIO_08 */ PIN_53, /* 28 - GPIO_30 */ PIN_64, /* 29 - GPIO_09 */ PIN_50, /* 30 - GPIO_00 */ PIN_17, /* 31 - GPIO_24 */ PIN_16, /* 32 - GPIO_23 */ PIN_60, /* 33 - GPIO_05 */ PIN_62, /* 34 - GPIO_07 */ PIN_18, /* 35 - GPIO_28 */ PIN_21, /* 36 - GPIO_25 */ PIN_64, /* 37 - GPIO_09 */ PIN_17, /* 38 - GPIO_24 */ PIN_01, /* 39 - GPIO_10 */ PIN_02 /* 40 - GPIO_11 */ }; CC3200 pinout: http://www.ti.com/ods/images/SWAS032F/po_DEV3200_swas032.gif CC3200MOD pinout: http://www.ti.com/ods/images/SWRS166/CC3200MOD_Pin_Diagram.gif Any thoughts or opinions would be very welcome!